Fits Dodge CHALLENGER 6" RACING STRIPES 5D Black CARBON FIBER vinyl Car Graphics

Description

NEW Fits Dodge Challenger 6" RACING STRIPES 5D Black CARBON FIBER vinyl Car Graphics
Description
You are purchasing a NEW:
Fits Dodge Challenger Single Racing Stripes, 5D Black Carbon Fiber vinyl Kit.
These NEW Carbon Fiber vinyl Racing Stripes were custom cut out by the owner of the Predator Corvette. Fits most vehicles.
The material is carefully cut, the Premium 5D Top Grade Shinny Gloss Carbon Fiber vinyl gives you a beautiful factory appearance.
When installing the Racing Stripes, make sure the
surfaces that you apply the material to must be smooth, non porous, and thoroughly cleaned from dust, grease, or any other contamination.
We are not responsible for improper installation.
If you have any questions before you purchase, please email us.
Our Vinyl is a dual cast file specifically designed to provide dimensional stability and durability without the need for an over laminate. The pressure-activated adhesive allows you to re-position the film until you apply firm pressure.
Whats included:
1. Qty 1, 6" x 60" for the Hood, Black Carbon Fiber Racing Stripes.
2. Qty 1, 6" x 36" for the Trunk, Black Carbon Fiber Racing Stripes.
3. Qty 1,
6" x 60" for the Roof, Black Carbon Fiber Racing Stripes.
These Racing Stripes are made of
Black carbon fiber vinyl, This is NOT REAL CARBON FIBER.
About the Carbon Fiber vinyl:
Re-positionable vinyl for trouble-free install
Strong self adhesive, peel and stick application. Just trim off excess with knife
Extremely high gross and smooth finish
Stretchable with heat
High temperature & water resistant
Install Temp: 60F to 80F (16C to 32C)
End Use Temp: -65F to 225F (-60C to 107C)
Easily cleansed with water and soap
Long lasting for around 4-5 yr outdoor / 12 yr indoor
Installation Tips:
This vinyl can be installed using 3M Primer 94 and 3M Edge sealer, these are recommended by 3M vinyl wrap training class, these products will promote adhesion and add life to your vinyl.
We would highly suggest using a 3M primer 94 or professional installation.
Installation Instructions:
1.
Make sure the
surfaces that you apply the material to is smooth, non porous, and thoroughly cleaned from dust, grease, or any other contamination.
2.  Use painters tape to a tape straight line down the car where you want the stripe to go to aid in lining up the decal. The carbon fiber vinyl racing stripes goes on the side of the tape. Carefully line up the decal to the desired position on the vehicle. Cut the vinyl to the desired length. (Note: you should have enough left over vinyl that you can use down the rear if you like.)
3. Peal off the backing from the decal exposing the adhesive side. Start from one side, stick the decal to the surface, then using a squeegee or a credit card wrapped in cloth to make sure it does not scratch the decal, start working your way to the other side of the decal applying pressure with the squeegee or credit card in order to remove the air bubbles.
4. When the vinyl has been applied, remove the clear film on the top.
5. If you still have air bubbles under the decal, use the squeegee or credit card to work the bubbles out. Start from the middle of the decal and work them out to the edge.
Shipping information:
Shipping in the USA: Free Shipping.
International Shipping: Shipping is calculated by your Country and zip codes. USPS Priority International (6-10 Business days)
International Buyers: We don't have knowledge of other country's laws outside of the USA so please make sure that your postal service will allow the item into your country before buying them. We are not responsible for custom taxes or levies your country may charge you.
Pictures sell!
Auctiva Free Image Hosting.
Show off your items with
Auctiva's Listing Templates
Auctiva,
THE simple solution for eBay sellers.
Track Page Views With
Auctiva's FREE Counter