10ft 3/4" Dual Wall 3:1 Adhesive-lined Heat Shrink Tubing Marine Cable Sleeve

Description

50x RV3.5-4 pre-Insulated Crimp Ring Ground Terminal Connector Black 14-12 AWG
8.99 USD
Free shipping
Black 3/4 Heat Shrink Tubes 3:1 Marine Grade Wire Wrap Adhesive Lined Waterproof
10.44 USD
10.99 USD
Free shipping
5%
off
RED HEAT SHRINK TUBING Sleeve Cable Wire Wrap Tube 3:1 Ratio 10Feet 1/8"
8.99 USD
Free shipping
50pcs Open Barrel Wire Crimp Copper Ring Lugs Terminals Connectors OT 20A
10.99 USD
Free shipping
500PCS Assorted Heat Shrink Electrical Wire Butt Connectors Crimp Terminals Kit
53.99 USD
Free shipping
280pcs HEAT SHRINK TUBING Sleeve Cable Wire Wrap Tube 2:1 Assortment Kit Box Set
12.34 USD
12.99 USD
Free shipping
5%
off
5/15/25 FEET 3/8" Heat Shrink Tubing Kit - 3:1 Dual Wall Tube w Adhesive -Blue
9.11 USD
9.59 USD
Free shipping
5%
off
100PCS 12-10 AWG Yellow Nylon Butt Electrical Wire Crimp Terminal Connector
14.29 USD
Free shipping
100-220PCS Assortment Heat Shrink Wire Connector Crimp Terminals Kit 22-10AWG
14.99 USD
Free shipping
250Pcs Heat Shrink Electrical Wire Connector Crimp Butt Ring Spade Terminals Set
24.69 USD
25.99 USD
Free shipping
5%
off
720PCS Heat Shrink Electrical Wire Connectors 10-22 Ring Spade Crimp Terminals
39.29 USD
Free shipping
60pcs Battery Cable Ends Copper Wire Lugs Terminal Connectors Assortment Kit
14.24 USD
14.99 USD
Free shipping
5%
off
100-300PCS Non-Insulated Bare Butt Connectors 22-10 AWG Terminals
10.99 USD
Free shipping
50PCS Blue Ring Cable Wire crimp Connector terminal block 16-14AWG RV2-3
8.99 USD
Free shipping
480PCS Assortment Crimp Terminals Heat Shrink Wire Connectors Marine Case Kit US
49.99 USD
Free shipping
5pcs OT-400A Copper Cable Lugs Ring Electrical Wiring Connectors Terminals
12.99 USD
Free shipping
3:1 Dual Wall Heat Shrink Tubing Glue Line Insulating Heat shrink Sleeve 64ft
41.79 USD
Free shipping
60-120PCS 2/3-Pin PCB Mount Screw Terminal Block Connector 5.0mm Pitch Blue
12.79 USD
Free shipping
Specification
Length: Black 5 Foot+Red 5 Foot
Material: Polyolefin
Heat shrink ratio: 3:1
Operating Temperature:-131°C to + 257℉
Shrinkage Temp: 212℉(Fahrenheit)
Full Shrinkage Temp: 230℉maximum
Tensile strength: 10.4Mpa
Dielectric strength: 15 kV / mm
Flammability: Flame Retardant
Adhesive lined shrink tubing is a 3:1 flexible tubing offering the advantages of integral, adhesive-lined construction. The tubing is made from flexible polyethylene with an internal layer of special thermoplastic adhesive. The heat-shrinkable outer wall is selectively cross-linked, while maintaining the high flow and excellent adhesion of the inner sealant liner. When heated in excess of 121ºC (250ºF), the tubing rapidly shrinks to a skintight fit, forcing the melted adhesive lining to flow and cover the substrate. The adhesive forms a flexible bond with a wide variety of rubbers, plastics and metals. Upon cooling, the adhesive solidifies, forming a permanent, non-drying, flexible and water resistant barrier. Adhesive reflow will occur at temperatures above 80ºC (176ºF).
Heat Shrink Tubing Detail
(HCHO), heavy metals and other harmful substances protecting you and your family from toxins
[The rubber liner has good sealing performance] Our heat-shrinkable tube has the advantages of good electrical insulation, good sealing, corrosion resistance and high temperature resistance. Anti-aging, tough, not easy to break.
[Easy and fast] You only need to heat it evenly with a hot air blower or a candle to make it shrink. It is a 3:1 heat shrink ratio and will shrink to the original 1/3.
[Versatile and DIY Helper]: High-quality heat shrink tubing, they can be used for solder joint protection, group of lines marking, resistance electric capacity reason protection etc. Note: Make sure temperature of your heat gun is up to 212℉(Fahrenheit), then glue inside will soften and seal the connection.
[Great Advantages ]: Our heat-shrinkable tube are with glue lined which has the advantages of good electrical insulation, good sealing, corrosion resistance and high temperature resistance. Anti-aging, tough, not easy to break.
[A wide range of applications] Shrink tube are mainly used for industrial, ship, wire links, anti-rust and anti-corrosion protection of solder joints, and audio and electrical DIY. Wire ends, harnesses, electronics protection and insulation treatment, fitness equipment parts and steel structure surface protection and so on.
About 3:1 Ratio Heat Shrink Tubing
What is it good for?
Industrial adhesive lined shrink tubing offers excellent protection for electronic components, wire splices, wire bundles and harness breakouts. Automotive, truck and marine wiring splices and harness breakouts are quickly and easily protected from harsh environments.
What is Shrink Ratio?
Industrial adhesive lined shrink tubing has a 3:1 shrink ratio. This means that the starting diameter of the tubing as supplied is 3 times the fully contracted diameter if allowed to completely shrink. The wall thickness of the tubing is proportional to the percentage of shrinkage.